Search results for " pressing"

Structural, optical, and luminescence properties of ZnO:Ga optical scintillation ceramic

2018

This paper discusses the characteristics of ZnO and ZnO:Ga ceramics fabricated by uniaxial hot pressing. The short-wavelength transmission limit of zinc oxide ceramics is in the 370-nm region; the long-wavelength limit is determined by the free-charge-carrier concentration and lies in the interval from 5 to 9 μm. The total transmittance of such ceramics in the visible and near-IR regions is about 70% when the sample is 0.5 mm thick. The luminescence spectrum is represented by a broad emission band with maximum at 580 nm, having a defect nature. The introduction of 0.03–0.1 mass % gallium into the zinc oxide structure inhibits grain growth and increases the free-charge-carrier concentration …

Lignin Inter-Diffusion Underlying Improved Mechanical Performance of Hot-Pressed Paper Webs

2021

Broader use of bio-based fibres in packaging becomes possible when the mechanical properties of fibre materials exceed those of conventional paperboard. Hot-pressing provides an efficient method to improve both the wet and dry strength of lignin-containing paper webs. Here we study varied pressing conditions for webs formed with thermomechanical pulp (TMP). The results are compared against similar data for a wide range of other fibre types. In addition to standard strength and structural measurements, we characterise the induced structural changes with X-ray microtomography and scanning electron microscopy. The wet strength generally increases monotonously up to a very high pressing tempera…

Mechanical properties of natural fiber composites produced using dynamic sheet former

2018

Composites formed from wood fibers and man-made cellulosic fibers in PLA (polylactic acid) matrix, manufactured using sheet forming technique and hot pressing, are studied. The composites have very low density (due to high porosity) and rather good elastic modulus and tensile strength. As expected, these properties for the four types of wood fiber composites studied here improve with increasing weight fraction of fibers, even if porosity is also increasing. On the contrary, for man-made cellulosic fiber composites with circular fiber cross-section, the increasing fiber weight fraction (accompanied by increasing void content) has detrimental effect on stiffness and strength. The differences …

Influences of atomization process and precursor material on the compaction mechanisms and metallurgical properties of parts developed by HIP

2022

Hot Isostatic pressing process is based on the densification of metals powders to near net shape parts with higher mechanicals properties than forged chemical equivalent. The precursor material can influence the parts properties. Thus the aims of this these is to understand the influence of the powder properties on the HIP parts. The particles characterization and the elements and compound monitoring during the HIP cycle allowed to understand the different oxidations phenomenons and their impact on the mechanical properties of parts. The comparison of differents powders batches with identical particles size repartition or identical chemical composition showed that the chemical composition a…

Dry Processing and Recycling of Thick Nacre–Mimetic Nanocomposites

2021

Acetaldehyde as a drug of abuse: insight into AM281 administration on operant-conflict paradigm in rats

2013

Increasing evidence focuses on acetaldehyde (ACD) as the mediator of the rewarding and motivational properties of ethanol. Indeed, ACD stimulates dopamine release in the nucleus accumbens and it is self-administered under different conditions. Besides the dopaminergic transmission, the endocannabinoid system has been reported to play an important role in ethanol central effects, modulating primary alcohol rewarding effect, drug-seeking and relapse behaviour. Drug motivational properties are highlighted in operant paradigms which include response-contingent punishment, a behavioural equivalent of compulsive drug use despite adverse consequences. The aim of this study was thus to characterize…

Thermoelectric properties of Zn-doped Ca_(3)AlSb_(3)

2012

Polycrystalline samples of Ca_(3)Al_(1)−_(x)Zn_(x)Sb_(3), with x = 0.00, 0.01, 0.02, and 0.05 were synthesized via a combined ball milling and hot pressing technique and the influence of zinc as a dopant on the thermoelectric properties was studied and compared to the previously reported transport properties of sodium-doped Ca_(3)AlSb_(3). Consistent with the transport in the sodium-doped material, substitution of aluminum with zinc leads to p-type carrier conduction that can be sufficiently explained with a single parabolic band model. It is found that, while exhibiting higher carrier mobilities, the doping effectiveness of zinc is lower than that of sodium and the optimum carrier concentr…

Enhanced thermoelectric performance in the p-type half-Heusler (Ti/Zr/Hf)CoSb0.8Sn0.2 system via phase separation

2014

A novel approach for optimization of the thermoelectric properties of p-type Heusler compounds with a C1b structure was investigated. A successful recipe for achieving intrinsic phase separation in the n-type material based on the TiNiSn system is isoelectronic partial substitution of Ti with its heavier homologues Zr and Hf. We applied this concept to the p-type system MCoSb0.8Sn0.2 by a systematic investigation of samples with different compositions at the Ti position (M = Ti, Zr, Hf, Ti0.5Zr0.5, Zr0.5Hf0.5, and Ti0.5Hf0.5). We thus achieved an approximately 40% reduction of the thermal conductivity and a maximum figure of merit ZT of 0.9 at 700 °C. This is a 80% improvement in peak ZT fr…

Study of interface formation during diffusion bonding : compact heat exchangers application

2014

Compact diffusion bonded heat exchangers are an attractive option in many fields (nuclear, (petro-)chemistry, solar…) due to their performance. This type of concept is especially intended for manufacturing the energy conversion system of the ASTRID reactor. During diffusion bonding by HIP, the problem is twofold: the channel deformation and microstructure evolution must be controlled, while at the same time, highly resistant interfaces are desired. This thesis is focused on the understanding and the control of the bonded components microstructure prepared by HIP in order to define « process » criteria to achieve welds in agreement with specifications of components containing fluidic channel…

Supplementing sleep actigraphy with button pressing while awake

2020

Objective/backgroundWrist-worn sleep actigraphs are limited for evaluating sleep, especially in sleepers who lie awake in bed without moving for extended periods. Sleep logs depend on the accuracy of perceiving and remembering times of being awake. Here we evaluated pressing an event-marker button while lying awake under two conditions: self-initiated pressing every 5 to 10 minutes or pressing when signaled every 5 minutes by a vibration pulse from a wristband. We evaluated the two conditions for acceptability and their concordance with actigraphically scored sleep.Participants and methodsTwenty-nine adults wore actigraphs on six nights. On nights 1 and 4, they pressed the marker to a vibra…